本科和硕士分别于2008年和2011年毕业于南昌航空大学和西南交通大学，2016年01月博士毕业于荷兰代尔夫特理工大学（Delft University of Technology， TU Delft）材料科学与工程专业。

1. 安赛罗米塔尔 (ArcelorMittal)-代尔夫特理工大学（TUDelft）联合基金，自增强耐磨钢的设计，2012.01-2015.12，12万欧（约100万人民币） 2. 国家自然科学基金面上项目 (51075324)，核电蒸汽发生器传热管高温微动损伤机理及防护研究，2011.01-2013.12，35万元，参与人

论文成果(Publications) (1)X. Xu, W. Xu, F.H. Ederveen, S. van der Zwaag, Design of low hardness abrasion resistant steels, Wear 301 (2013) 89-93. (2)X. Xu, S. van der Zwaag, W. Xu, A novel multi-pass dual-indenter scratch test to unravel abrasion damage formation in construction steels, Wear 322-323 (2015) 51-60. (3)X. Xu, S. van der Zwaag, W. Xu, Prediction of the abrasion resistance of construction steels on the basis of the subsurface deformation layer in a multi-pass dual-indenter scratch test,Wear 338-339 (2015) 47-53. (4)X. Xu, S. van der Zwaag, W. Xu, The effect of martensite volume fraction on the scratch and abrasion resistance of a ferrite-martensite dual phase steel, Wear 348-349 (2016) 80-88. (5)X. Xu, S. van der Zwaag, W. Xu, The scratch and abrasive wear behaviour of a tempered martensitic construction steel and its dual phase variants, Wear 358-359 (2016) 80-88. (6)X. Xu, S. van der Zwaag, W. Xu. Abrasion resistance characterization of low alloy construction steels: A comparison between three different scratch test protocols. Wear. 2017;384-385:106-13. (7)X. Xu, S. van der Zwaag, W. Xu, The effect of ferrite-martensite morphology on the scratch and abrasive wear behavior of a dual phase construction steel, Wear 348-349 (2016) 148-157. (8)X. Xu, F.H. Ederveen, S. van der Zwaag, W. Xu, Correlating the abrasion resistance to the standard mechanical properties of low alloyed steels: a statistical analysis over a larger data set, Wear, 368-369 (2016) 92-100. (9)H. Chen, X. Xu, W. Xu, S. van der Zwaag, Predicting the austenite fraction after intercritical annealing in lean steels as a function of the initial microstructure, Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science 45 (2014) 1675-1679. (10)H.W. Liu, X.J. Xu, M.H. Zhu, P.D. Ren, Z.R. Zhou, High temperature fretting wear behavior of WC25Co coatings prepared by D-gun spraying on TiAlZr titanium alloy, Tribology International 44 (2011) 1461-1470. (11)徐小军; 刘捍卫; 朱旻昊; 邱绍宇; 周仲荣. Ti-Al-Zr钛合金的高温微动磨损行为研究, 核动力工程31(2010)42-47 (12)W. Xu, Q. Lu, X. Xu, S. van der Zwaag, The structure of a general materials genome approach to the design of new steel grades for specific properties, Computer Methods in Materials Science 13 (2013) 382-394. Conference proceedings 1) Xiaojun Xu, Sybrand van der Zwaag, Wei Xu, The effect of ferrite-martensite morphology on scratch and abrasion behaviour of low alloyed DP steels, 42th Leeds-Lyon Symposium on Tribology 2015, Lyon, France. (Oral presentation) 2) Xiaojun Xu, Sybrand van der Zwaag, Wei Xu, The effect of martensite volume fraction in a dual phase steel on the scratch behaviour in a multi-pass dual-indenter scratch test and its correlation with abrasion resistance, 20th International Conference on Wear of Materials 2015, Toronto, Canada. (Oral presentation) 3) Xiaojun Xu, Sybrand van der Zwaag, Wei Xu, A novel multi-pass dual-indenter scratch test to unravel abrasion damage formation in construction steels, 41st Leeds-Lyon Symposium on Tribology 2014, Leeds, UK. (Oral presentation) 4) Xiaojun Xu, Sybrand van der Zwaag, Wei Xu, A study into the correlation between abrasion resistance and steel microstructures using single and multiple scratching, European Symposium on Friction, Wear and Wear protection 2014, Karlsruhe, Germany. (Oral presentation) 5) Xiaojun Xu, Sybrand van der Zwaag, Wei Xu, A novel multi-pass dual-indenter scratch test to unravel abrasion damage formation in construction steels, European Symposium on Friction, Wear and Wear protection 2014, Karlsruhe, Germany. (Poster) 6) Xiaojun Xu, Wei Xu, Sybrand van der Zwaag, Design of low hardness abrasion resistant steels, WOM 2013, Portland, US. (Oral presentation) 7) Xiaojun Xu, Wei Xu, Sybrand van der Zwaag, A study on correlating microstructural features with abrasion resistance of a high strength low alloy steel, SCAD 2013, Ghent, Belgium. (Oral presentation) 8) Xiaojun Xu, Wei Xu, Sybrand van der Zwaag, Designing abrasion resistant steels using reported correlations between abrasion resistance, mechanical properties and microstructure in advanced steels, MSE 2012, Darmstadt, Germany. (Oral presentation) 9) Xiaojun Xu, Wei Xu, Sybrand van der Zwaag, Computational design of high abrasion resistance - Low hardness multiple phase steels, National Student Conference in Metallic Materials 2012, Manchester, UK. (Oral presentation)